Early 03 Sedan, Bought Hypertech, EARLY ECU GUYS, TAKE A LOOK
#16
Join Date: May 2007
Location: Northeast
Posts: 669
Likes: 0
Received 0 Likes
on
0 Posts
Also, I agree on your comment about the Maxima community. I've made mention of the similarities between the early G35 ECU and the VQ Maximas to Hypertech. Maybe they will come out with something.
#18
Join Date: May 2007
Location: Northeast
Posts: 669
Likes: 0
Received 0 Likes
on
0 Posts
Final Update Before the Weekend:
Early ECU support IS offered.
In other words, Hypertech isn't going to say they support 03-06 G35s and simply forget about the early ECU. All ECUs will be covered by the programmer, and we're just waiting on the tech team to finish making the code for the early ECU. Hypertech says that they don't think it'll be a big hurdle to offer support for the early ECU, so stay tuned for next week! Maybe something exciting will happen.
Early ECU support IS offered.
In other words, Hypertech isn't going to say they support 03-06 G35s and simply forget about the early ECU. All ECUs will be covered by the programmer, and we're just waiting on the tech team to finish making the code for the early ECU. Hypertech says that they don't think it'll be a big hurdle to offer support for the early ECU, so stay tuned for next week! Maybe something exciting will happen.
#19
Red Card Crew
iTrader: (24)
IMHO, they might as well be starting over. Hope they can do that. The only other company that has done it is Technosquare.
but thanks for the effort and I hope it works out for you because that means the rest of us will have options. Now start bugging them about a tranny ecu reflashes! lol
I know hypertech does domestic tranny ecu modifications. so crossing my fingers
but thanks for the effort and I hope it works out for you because that means the rest of us will have options. Now start bugging them about a tranny ecu reflashes! lol
I know hypertech does domestic tranny ecu modifications. so crossing my fingers
#21
Join Date: May 2007
Location: Northeast
Posts: 669
Likes: 0
Received 0 Likes
on
0 Posts
#23
Join Date: May 2007
Location: Northeast
Posts: 669
Likes: 0
Received 0 Likes
on
0 Posts
In terms of an update, Chris and I traded e-mails on Friday, but I'm not sure if Hyptertech wants me to release the information we exchanged. It's interesting, and we'll see what happens. They have not given up the fight
#26
Join Date: May 2007
Location: Northeast
Posts: 669
Likes: 0
Received 0 Likes
on
0 Posts
I am calling Hypertech tomorrow. The early ECU does not have a certain pin in the OBDII port like the later ECUs. They were not getting a signal back from the ECU because there was nothing there to send/receive!
Chris said this wasn't a deal breaker, so I'll see what they have for me tomorrow.
Chris said this wasn't a deal breaker, so I'll see what they have for me tomorrow.
#28
Join Date: May 2007
Location: Northeast
Posts: 669
Likes: 0
Received 0 Likes
on
0 Posts
Hmmm this?
http://uprev.com/documentation/2003%...%20re-wire.pdf
Sounds like they are still at square 1. Good luck!
http://uprev.com/documentation/2003%...%20re-wire.pdf
Sounds like they are still at square 1. Good luck!
I sure hope they're not on square one...
#30
Join Date: May 2007
Location: Northeast
Posts: 669
Likes: 0
Received 0 Likes
on
0 Posts
EDIT: Sent out the calibration! Hypertech said that it'll most likely be ready on Monday! It looks like thew programmer is a go unless they run into some issue with the calibration, but, IMO, that's unlikely. I'll keep everyone posted!
Last edited by MM_G3520; 08-19-2010 at 11:50 AM.