Help! no sound after doudle din install!!
#1
Join Date: May 2005
Location: east lansing,MI
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
Help! no sound after doudle din install!!
okay i just finished installing a alpine HU and 4 channel amp. everything works fine except i get no sound coming out. i double checked all the wires but i can't figure it out. i used a bestbuy wiring harness if that helps. i searched and some said to connect the power antenna with the ground amp and ground wire, tried that but no luck. Any ideas?? thanks
#3
Join Date: May 2005
Location: east lansing,MI
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
#7
Does the amp have a power status light on it? is it on?
Also what preamps are you plugging that amp into the back of your deck?
Make sure your deck preamps are enabled in your deck options..?
Did you run wires to all the speakers from the new amp or did you tap the ones going to the bose amp?
Just trying to get a better understanding of whats going on. It will be a lot easier to help you once these things are clarified.
Also what preamps are you plugging that amp into the back of your deck?
Make sure your deck preamps are enabled in your deck options..?
Did you run wires to all the speakers from the new amp or did you tap the ones going to the bose amp?
Just trying to get a better understanding of whats going on. It will be a lot easier to help you once these things are clarified.
Trending Topics
#8
Join Date: May 2005
Location: east lansing,MI
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
sorry for the confusion guys, i'll try to clear it up alittle. okay for the wiring harness i connected everything but the power antenna, and illumination. grounded the amp turn on and the ground wire together. i channeled the power, remote turn on, and RCA wires all to the trunk. the ground wire for the amp i just screwed to the chassis(sanded off the paint first). Now for the for bose speaker wires i just tapped the bose wiring harness.
got the bose wiring info from this thread: https://g35driver.com/forums/showthr...ght=bose+wires
hope this clears things up for you guys. again, i thank everyone for your inputs.
got the bose wiring info from this thread: https://g35driver.com/forums/showthr...ght=bose+wires
hope this clears things up for you guys. again, i thank everyone for your inputs.
#10
Join Date: May 2005
Location: east lansing,MI
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
#11
To turn on, your amp needs constant +12 volts from the battery, a ground, and +12 volts to the turn on lead, which turns on the amp.
If, as you posted, you connected the amp turn on to ground, then no +12 volts is going to the amp. You can connect the turn on lead to the power antenna lead.
If, as you posted, you connected the amp turn on to ground, then no +12 volts is going to the amp. You can connect the turn on lead to the power antenna lead.
#12
Join Date: May 2005
Location: east lansing,MI
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
i think i know what your trying to say. so i should connect the amp turn on wire(black/white) and power antenna(blue) together and ground it to get the 12v, or connect the power antenna(blue) and remote turn on(blue/white) together to get that 12v?
Last edited by vietster; 04-30-2007 at 06:32 PM.
#15
Join Date: May 2005
Location: east lansing,MI
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts