Warning another NOOB!
#16
The RACK for you
So bought the new A/C condenser.
Got tranny fluid.
I think I have ALL the bits for the initial run & drive...
Except a few connectors...
Then it's on to safety ( I know SISSY ).
Got a pass side air bag.
Some go fast sillycone coolant hoses.
Stock front rotors & pads.
and the HI PO hood prop & grommet
At the rate it going about 2 more weeks..
Need 1/8 of an inch on the top subframe rail, before the new sheetmetal gets put back on...
MAJOR PROP'S to Ritchie @ A&K Frame & alignment
25834 Springbrook Ave
Santa Clarita, CA 91350
(661) 259-3228
A TRUE old school craftsman !!!!!
Everything is inspected & triple checked and done 100%!
So there you have it...
Mike
Got tranny fluid.
I think I have ALL the bits for the initial run & drive...
Except a few connectors...
Then it's on to safety ( I know SISSY ).
Got a pass side air bag.
Some go fast sillycone coolant hoses.
Stock front rotors & pads.
and the HI PO hood prop & grommet
At the rate it going about 2 more weeks..
Need 1/8 of an inch on the top subframe rail, before the new sheetmetal gets put back on...
MAJOR PROP'S to Ritchie @ A&K Frame & alignment
25834 Springbrook Ave
Santa Clarita, CA 91350
(661) 259-3228
A TRUE old school craftsman !!!!!
Everything is inspected & triple checked and done 100%!
So there you have it...
Mike
Last edited by vigman; 06-12-2011 at 01:07 PM.
#17
Progress report
The frame is now the correct length, the correct sub frame pieces are here & going on next week, I also now have the correct rear rims & tires. the suspension on the pass side is 100%. Delivered the battery, pass side fender, silicone hoses, squirter rez & fill neck. I have the pass side air bag now.
and all the connectors for items that got CRUSHED in the accident.
I'll have a day or so in repinning & testing sub systems.
I'm happy with the progress..
Last bits would be pass side interior door grab.
Front seat belts & repair of the dash pad ( or dash replacement ) .
and all the connectors for items that got CRUSHED in the accident.
I'll have a day or so in repinning & testing sub systems.
I'm happy with the progress..
Last bits would be pass side interior door grab.
Front seat belts & repair of the dash pad ( or dash replacement ) .
#18
Ok more progress
https://g35driver.com/forums/members...r-project.html
Today, delivered the hood,O rings for the A/C, more wiring harness...front bumper & energy absorber.
All the frame work is done, and now it's dry fitting time and it all looks great.....
The front rims are on the back and the back is on the front ( great! ).
So more news as it's available.
Mike
https://g35driver.com/forums/members...r-project.html
Today, delivered the hood,O rings for the A/C, more wiring harness...front bumper & energy absorber.
All the frame work is done, and now it's dry fitting time and it all looks great.....
The front rims are on the back and the back is on the front ( great! ).
So more news as it's available.
Mike
Last edited by vigman; 06-25-2011 at 09:29 PM.
#20
So it's 4th of July weekend and the shop is taking a long weekend.
BUT I was able to stop by....
We are here:
The front pass side loom and all connectors are repaired and looking factory!
I did have to point out what connectors when where, which is difficult since 1/2 the front end bits are all over the shop...
New arrivals on parts:
Scored a drivers side seat belt ( not blown ).
Scored a front license bracket.
Scored a new grille ( non stock ).
The new stock rotors & pads are in..
The power steering lines are going back in ( since 2 were crushed in the PO's accident ).
Optima battery is in & all blown fuses in that STUPID panel behind the battery are replaced.
Glass goes in next week.
Drivers side fender ( had a few dings from the crash ) are paint ready.
All the frame bits that were replaced, or adaptor's, brackets used on the pull are removed, painted factory color & finished to factory.
So next week....
Fenders, hood, radiator core support all go to final bolt up and finish alignment
Power steering finalized, Cooling system installed, Auto tranny lines fixed & system topped off. AC condensor High side switch installed and all lines resealed..
Start up and verify that tranny works ( it did for a bit, till most of the fluid bled out on my driveway!) verify mechanicals
Misc parts needed....
Need the resonator that goes below the air cleaner assy.
One of the top radiator twist locks is missing & one lower radiator grommet is missing.
Now I know why these cars usually are not brought back from the dead....
This is getting expensive!! BUT I know it will be great when done..
Happy 4th!
Mike
BUT I was able to stop by....
We are here:
The front pass side loom and all connectors are repaired and looking factory!
I did have to point out what connectors when where, which is difficult since 1/2 the front end bits are all over the shop...
New arrivals on parts:
Scored a drivers side seat belt ( not blown ).
Scored a front license bracket.
Scored a new grille ( non stock ).
The new stock rotors & pads are in..
The power steering lines are going back in ( since 2 were crushed in the PO's accident ).
Optima battery is in & all blown fuses in that STUPID panel behind the battery are replaced.
Glass goes in next week.
Drivers side fender ( had a few dings from the crash ) are paint ready.
All the frame bits that were replaced, or adaptor's, brackets used on the pull are removed, painted factory color & finished to factory.
So next week....
Fenders, hood, radiator core support all go to final bolt up and finish alignment
Power steering finalized, Cooling system installed, Auto tranny lines fixed & system topped off. AC condensor High side switch installed and all lines resealed..
Start up and verify that tranny works ( it did for a bit, till most of the fluid bled out on my driveway!) verify mechanicals
Misc parts needed....
Need the resonator that goes below the air cleaner assy.
One of the top radiator twist locks is missing & one lower radiator grommet is missing.
Now I know why these cars usually are not brought back from the dead....
This is getting expensive!! BUT I know it will be great when done..
Happy 4th!
Mike
#21
Don't buy the resonator but instead do this mod
https://g35driver.com/forums/engine-...-anti-56k.html
https://g35driver.com/forums/engine-...-anti-56k.html
#22
#24
Less than 2 weeks to go....
Windshield in! ( and they broke the first one DOH! )
Adding magic fluid ( 5 qts of Nissan ATF ) and now the tranny actually functions.
All wiring in & tested..
Have to find more parts, inner fender skirts and such.....
First color goes on tuesday~!
There are some MINOR fitment issues but nothing major~
She fires right up....
We're SO CLOSE!
Mike
Windshield in! ( and they broke the first one DOH! )
Adding magic fluid ( 5 qts of Nissan ATF ) and now the tranny actually functions.
All wiring in & tested..
Have to find more parts, inner fender skirts and such.....
First color goes on tuesday~!
There are some MINOR fitment issues but nothing major~
She fires right up....
We're SO CLOSE!
Mike
#26
Out of Paint
https://g35driver.com/forums/members...r-project.html
So left to go...
Pinstriping
Pass side front inner fender covers
Fit front grille better
Smog under hood stickers
Charge AC
Factory stereo ( just to get AC working )
Then belts, air bags Pass side interior door panel..
Clean & detail
Smog, Lights & brake inspection, VIN inspection...
THEN the fun stuff!
Mike
https://g35driver.com/forums/members...r-project.html
So left to go...
Pinstriping
Pass side front inner fender covers
Fit front grille better
Smog under hood stickers
Charge AC
Factory stereo ( just to get AC working )
Then belts, air bags Pass side interior door panel..
Clean & detail
Smog, Lights & brake inspection, VIN inspection...
THEN the fun stuff!
Mike
#28