PPE Engineering LongTube Headers
#186
If I was 6mt I would of made close to 300 or more. The headers with cams held 280+hp from 6100-7200.
#187
#189
#191
dsskyline
that vid you posted a while back showing your rpms on the 125 shot concerned me a little. at about 4500 the hesitation you have coresponding with the power loss at that point, something is going on there. since you have moved your floor mat, does it still hesitate like that?
i should have some numbers soon, i do not have long tubes, but nismo headers and test pipes with bc stage 2 cams and a cutout after the xyz pipe. im also an auto, so results should be interesting.
i would think you should be about 425 hp on a 125 shot
that vid you posted a while back showing your rpms on the 125 shot concerned me a little. at about 4500 the hesitation you have coresponding with the power loss at that point, something is going on there. since you have moved your floor mat, does it still hesitate like that?
i should have some numbers soon, i do not have long tubes, but nismo headers and test pipes with bc stage 2 cams and a cutout after the xyz pipe. im also an auto, so results should be interesting.
i would think you should be about 425 hp on a 125 shot
#192
dsskyline
that vid you posted a while back showing your rpms on the 125 shot concerned me a little. at about 4500 the hesitation you have coresponding with the power loss at that point, something is going on there. since you have moved your floor mat, does it still hesitate like that?
i should have some numbers soon, i do not have long tubes, but nismo headers and test pipes with bc stage 2 cams and a cutout after the xyz pipe. im also an auto, so results should be interesting.
i would think you should be about 425 hp on a 125 shot
that vid you posted a while back showing your rpms on the 125 shot concerned me a little. at about 4500 the hesitation you have coresponding with the power loss at that point, something is going on there. since you have moved your floor mat, does it still hesitate like that?
i should have some numbers soon, i do not have long tubes, but nismo headers and test pipes with bc stage 2 cams and a cutout after the xyz pipe. im also an auto, so results should be interesting.
i would think you should be about 425 hp on a 125 shot
I will make another vid when I go to RT next week. The dyno I did last week had me very rich in that range. Now that I can go fully WOT now my tune is off due to them trying to tune out my power loss.
Hopefully I will have good numbers and my lowend issue is solved.
My car with the DLC coated buckets revs faster to me due to less friction.
SDgenius my 3.7FD goes in tonight I can't wait to try it out.
#193
your rpms are going to fly up soooo fast with spray and 3.7s, then on top of that if you get a higher stall converter it will be even worse. i would keep the stock 3.5s or 3.3s, whatever you are stock, around just in case it revs too fast for you
its good that the hesitation is gone, its weird that the throttle would do it like that because just below that 4500rpm spot, the needle was climbing like crazy. i would have thought that if it was the floor mat, it would have been uniform all the way though the rpm range
excited to see updated numbers, wish i would have known about the HR buckets before mine went together. o well. im mgrotel over on my350z
its good that the hesitation is gone, its weird that the throttle would do it like that because just below that 4500rpm spot, the needle was climbing like crazy. i would have thought that if it was the floor mat, it would have been uniform all the way though the rpm range
excited to see updated numbers, wish i would have known about the HR buckets before mine went together. o well. im mgrotel over on my350z
#194
We have talked through PM on my350z I'm denchan350gt over there.
I know about the revs I only spray at the track on slicks or DR's. The 3.7 is for a more enjoyable/fun N/A experience with my power.
I might need not the higher stall if my lowend issue is resolved. I was pulling 1.8-1.9 60fts before my issue.
The 3.7 is the best for a N/A 5AT. F/I would be 3.3 or 3.5.
How is the car is it done completely? I wonder what you will put down since you are AT also.
I know about the revs I only spray at the track on slicks or DR's. The 3.7 is for a more enjoyable/fun N/A experience with my power.
I might need not the higher stall if my lowend issue is resolved. I was pulling 1.8-1.9 60fts before my issue.
The 3.7 is the best for a N/A 5AT. F/I would be 3.3 or 3.5.
How is the car is it done completely? I wonder what you will put down since you are AT also.
#195