MREV+ installed on a NON REVUP engine!
#272
#273
Anxiously awaiting more dyno results! I'm hoping the MREV 2 will produce TQ (especially in the mid range)... This is what I've been after for quite a while. I'm absolutely not concerned about max hp - I'm okay in that department and unless this kills high rmp hp, I am still interested – as long as it provides mid TQ!
#278
#279
Aznteazer,
go here http://www.motordyneengineering.com/
click DYNOS link, you will find all kind of spacer
dyno results there
Mike
go here http://www.motordyneengineering.com/
click DYNOS link, you will find all kind of spacer
dyno results there
Mike
#280
Modded Member
iTrader: (20)
Just completed the MREV2 install on my 2005 5AT sedan. I was skeptical at first, but damn, I can certainly feel the difference throughout the revrange. It brought back some power down low, added a ton in the midrange, and keeps pulling till I hit redline. This is certainly the best bang for buck mod I have purchased.
However, my plenum is still hot to the touch after driving. I ordered the copper iso thermal 5/16" spacer and the MREV2 lower collector.
Any ideas?
However, my plenum is still hot to the touch after driving. I ordered the copper iso thermal 5/16" spacer and the MREV2 lower collector.
Any ideas?
#281
Originally Posted by vodkarocket
Just completed the MREV2 install on my 2005 5AT sedan. I was skeptical at first, but damn, I can certainly feel the difference throughout the revrange. It brought back some power down low, added a ton in the midrange, and keeps pulling till I hit redline. This is certainly the best bang for buck mod I have purchased.
However, my plenum is still hot to the touch after driving. I ordered the copper iso thermal 5/16" spacer and the MREV2 lower collector.
Any ideas?
However, my plenum is still hot to the touch after driving. I ordered the copper iso thermal 5/16" spacer and the MREV2 lower collector.
Any ideas?
The upper collector will still be hot to the touch. However, you should have noticed that the heat is bearable, now. Just to be sure . . . The rubber insulating gasket, which came fixed to the copper plate was installed facing the plenum neck, right?
In any event, have a blast with your newest mod and try to keep the speeding down to a minimal.
#282
Registered User
iTrader: (1)
Join Date: Nov 2005
Location: SF,CA
Posts: 223
Likes: 0
Received 0 Likes
on
0 Posts
what intake are you running with this?
Originally Posted by vodkarocket
Just completed the MREV2 install on my 2005 5AT sedan. I was skeptical at first, but damn, I can certainly feel the difference throughout the revrange. It brought back some power down low, added a ton in the midrange, and keeps pulling till I hit redline. This is certainly the best bang for buck mod I have purchased.
However, my plenum is still hot to the touch after driving. I ordered the copper iso thermal 5/16" spacer and the MREV2 lower collector.
Any ideas?
However, my plenum is still hot to the touch after driving. I ordered the copper iso thermal 5/16" spacer and the MREV2 lower collector.
Any ideas?
#283
Originally Posted by mikesj
Aznteazer,
go here http://www.motordyneengineering.com/
click DYNOS link, you will find all kind of spacer
dyno results there
Mike
go here http://www.motordyneengineering.com/
click DYNOS link, you will find all kind of spacer
dyno results there
Mike
i was looking specifically for Mrev++ with 5/16" spacer on a 280hp engine.
too much to ask for but i dont wanna lose power either
#284
Aznteaser,
this thread answers all your questions
http://my350z.com/forum/showthread.php?t=188419
Mike
this thread answers all your questions
http://my350z.com/forum/showthread.php?t=188419
Mike