Forced Induction Discussion of turbos , superchargers , and nitrous upgrades on the G35

JZurita's Build = Performance Factory Nightmare (MUST READ)

Thread Tools
 
Search this Thread
 
Rate Thread
 
  #1  
Old 09-29-2009, 04:15 PM
jzurita's Avatar
Registered User
Thread Starter
Join Date: Oct 2008
Posts: 106
Likes: 0
Received 0 Likes on 0 Posts
JZurita's Build = Performance Factory Nightmare (MUST READ)

:wave: Just thought I'd share...

http://my350z.com/forum/shop-builds/...-octane-9.html

For those that don't feel like reading through everything, here is a synopsis of what's going on:

Fall of 2007 I decided to get rid of my JWT setup and go built w/ Greddy TT's. I was referred to a thread created by Mr. Tibbs where he offered a great deal on built blocks, shipped to your door. The plan was to have the block shipped to a local performance shop and get it installed and tuned there while I was away for the holidays. The shop I was dealing with at the time was "The Shop" in Norwalk, CT.

On 12/2007, the block was delivered to "The Shop" and the following day I went on vacation for two weeks. When I got back I was anxious to see how the build had gone and called them. Almost a week passed and I had yet to receive a call back, so I drove there unannounced to check out the build. I was shocked to see my car sitting in the corner of the lot, surrounded by snow, and motorless. I could tell it had been left there for days.

I spoke to Jimmy (the owner) and he tells me that the JT block looked like it was a rebuilt motor and he refused to let my car leave with it installed. Then he shows me the block and I proceed to record a vid (as seen below).

Jimmy calls JT and goes in the other room to have a manager-o-manager chit chat. After all the yelling, Jimmy hands me the phone and I talk to JT about the issue. JT claims that he did not ship the motor in the condition Jimmy described and that he single-handedly built it.

After showing JT the vid, the story changed a bit and it turned into one of his techs screwing up the build and not getting it "cleaned" properly. JT assured me that the block was fine, that it was the strongest running block he had ever built, and that I should just install it. There was also scraps of metal found in the oil pan. When I asked about it, JT told me that he just threw the pan on there, but that it didn’t come from the same block.

Okay, at this point you're probably thinking, WHY THE *** DIDN'T YOU SHIP IT BACK TO JT!? Well, I would have been 100% on "The Shop's" side if it wasn't for the fact that they never returned any of my calls, pulled the motor out before checking the one coming in, AND tried to up sell me on getting my build done there. I also started hearing horror stories about "The Shop", including Randy's nightmare. For all I knew, they could have easily installed the block while I was gone, blown in up, and uninstalled it before I got back from vacation. That would explain why my car was motorless, the unreturned calls, and the refusal to install the block.

At this point I didn't know who to believe, as both shops were pointing fingers at each other. "The Shop" was absolutely no help. They never returned ANY of my calls and were purposely very unhelpful with the entire situation. It was either I pay them to rebuild the motor, or nothing. JT on the other hand offered to pay to get my car shipped to him and assured me that he would take care of everything. At the time all this happened, Performance Factory was doing great and I heard nothing but good feedback from everyone that went to JT. So I, of course decided to accept JT's offer and had my car shipped to him.

"The Shop" was pissed, to say the least. Now I wish I had just returned the block as soon as I received it. Unfortunately, thanks to great marketing and misinformation on the forums, here I stand.

For your enjoyment, here is the long-lost tape. And yes, the tear-down vid is worse.

http://v3.tinypic.com/player.swf?file=28iyla8&s=3

Here are a few pictures:
http://projectz33.com/100_0587.JPG
http://projectz33.com/100_0588.JPG
http://projectz33.com/100_0589.JPG
http://projectz33.com/100_0593.JPG
http://projectz33.com/100_0601.JPG

The car was shipped right back with the understanding that JT would take full responsibility for "his tech's error". He led me to believe that everything would be torn apart and rebuilt from scratch.

I didn't get the car back till 8/2008 and the motor blew on 05/2009. That's a total of 9 months and 4,000 miles. The car was not tracked or beaten on. I immediately contact JT regarding the motor and he insisted that I ship the car back to him so that he can fix it. He also mentioned that he didn't want me to bring it to another shop because his competition always tries to point fingers at him. So what did I do? I towed it to VTR...



Here is the original invoice that was emailed to me, including a breakdown of what was SUPPOSED to be done:
http://projectz33.com/Est_1214_from_Performance_F.pdf


Here's the link to the teardown vid: http://blip.tv/file/2670987

There's not much I can say at this point other than I'm disgusted. I'm not the only one he has fuked over and definitely won't be the last. It seems like his plan is to move from platform to platform and get away with whatever he can. As soon as **** hits the fan, the shop closes, someone's in the hospital, there's been a death in the family, etc... Spread the word as much as you can, as this guy needs to be banished from the industry. Friends don't let friends get scammed by Jeremy Tibbs.

Thanks - Jon
 

Last edited by jzurita; 10-22-2009 at 11:43 AM.
  #2  
Old 09-29-2009, 04:20 PM
jzurita's Avatar
Registered User
Thread Starter
Join Date: Oct 2008
Posts: 106
Likes: 0
Received 0 Likes on 0 Posts
Skip to page 9 for the fail/win.
 
  #3  
Old 09-29-2009, 04:42 PM
GreenGoblin's Avatar
The goblin resurrection

iTrader: (66)
Join Date: Oct 2006
Location: In my garage
Posts: 25,863
Received 187 Likes on 95 Posts
Sorry to hear that you are going thru this.
 
  #4  
Old 09-29-2009, 05:40 PM
escobar929's Avatar
Registered User
iTrader: (9)
Join Date: Nov 2004
Location: Hollywood, FL
Posts: 14,074
Likes: 0
Received 3 Likes on 3 Posts
very sad to see bro
 
  #5  
Old 09-29-2009, 06:04 PM
G U LATER's Avatar
Registered User
iTrader: (9)
Join Date: May 2008
Location: Orlando, FL
Posts: 5,062
Likes: 0
Received 0 Likes on 0 Posts
dang that sucks to see
 
  #6  
Old 09-29-2009, 06:38 PM
WhosRich's Avatar
Registered User
iTrader: (13)
Join Date: Oct 2006
Location: New York, NY
Posts: 1,958
Likes: 0
Received 6 Likes on 6 Posts
I tried to read through all the pages, and i can see the fail, but wheres the win really? and why are the my350z guys so mad at Driver?
 
  #7  
Old 09-29-2009, 06:50 PM
TIAN's Avatar
Hold The Line

iTrader: (20)
Join Date: Oct 2006
Location: SFL
Posts: 17,779
Received 622 Likes on 406 Posts
That sucks bro. Are you gonna go after JT? I havent heard from him since PF went down.
 
  #9  
Old 09-30-2009, 08:04 AM
jzurita's Avatar
Registered User
Thread Starter
Join Date: Oct 2008
Posts: 106
Likes: 0
Received 0 Likes on 0 Posts
Thanks guys. The teardown vid should be up tonight or tomorrow.

Originally Posted by WhosRich
I tried to read through all the pages, and i can see the fail, but wheres the win really? and why are the my350z guys so mad at Driver?
 
  #10  
Old 09-30-2009, 12:44 PM
XKR's Avatar
XKR
XKR is offline
Registered User
Join Date: Mar 2007
Location: Sugar Land TX/Boca Raton FL/Carefree AZ
Posts: 786
Likes: 0
Received 8 Likes on 3 Posts
Originally Posted by HomieG35
I'm going to dread getting my engine built...
Pick the right shop and you will be fine.....Here are a few IMO are some of the best..

Forged Performance
GTM
Intense Motorsport
Injected Motorsport
Sound performance
Speed Force Racing
JTran
Protec

Just to name a few. You are in the Houston area....JTran is in Conroe.....Protec is in Austin..and they program the F-con. They have worked on my car before.

Originally Posted by WhosRich
I tried to read through all the pages, and i can see the fail, but wheres the win really? and why are the my350z guys so mad at Driver?
They do not have any issues with G35driver.....They have issues with some of the Mods/Admin like Calvin...(thats the only name i can think of at this moment)....I myself have had to contact IB on behalf of myself and others....


Sorry JZ for OT.
 

Last edited by XKR; 09-30-2009 at 12:50 PM.
  #11  
Old 09-30-2009, 01:11 PM
jzurita's Avatar
Registered User
Thread Starter
Join Date: Oct 2008
Posts: 106
Likes: 0
Received 0 Likes on 0 Posts
^ It's all good man. Fancy seeing you here.
 
  #12  
Old 09-30-2009, 01:25 PM
WILLIE BEANS's Avatar
Registered User
iTrader: (3)
Join Date: May 2007
Location: pinellas county FLA, queens N.Y.
Posts: 4,383
Received 27 Likes on 21 Posts
hope everything goes well..
 
  #13  
Old 09-30-2009, 01:58 PM
XKR's Avatar
XKR
XKR is offline
Registered User
Join Date: Mar 2007
Location: Sugar Land TX/Boca Raton FL/Carefree AZ
Posts: 786
Likes: 0
Received 8 Likes on 3 Posts
Originally Posted by jzurita
^ It's all good man. Fancy seeing you here.
I get around
 
  #14  
Old 10-01-2009, 09:57 PM
350 Rookie's Avatar
Registered User
iTrader: (2)
Join Date: Aug 2009
Location: Cheshire, CT
Posts: 75
Likes: 0
Received 0 Likes on 0 Posts
Hey jon. Im banned from that forum. Can you just tell me whats going on. lol
 
  #15  
Old 10-06-2009, 12:58 PM
jzurita's Avatar
Registered User
Thread Starter
Join Date: Oct 2008
Posts: 106
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by 350 Rookie
Hey jon. Im banned from that forum. Can you just tell me whats going on. lol
I'll put together a synopsis for the banned/lazy bums on here.
 


You have already rated this thread Rating: Thread Rating: 0 votes,  average.

Quick Reply: JZurita's Build = Performance Factory Nightmare (MUST READ)



All times are GMT -4. The time now is 05:18 PM.