Motordyne - Tony
Former G35driver Vendor
iTrader: (23)
Joined: Jul 2004
Posts: 3,054
Likes: 85
From: Los Angeles California
Originally Posted by twin001
So for an existing TD system we would have to do a custom modification to fit with the new flipped collector?
just another question to throw out there, the VQ exhaust you have, just how "quite" is it.....more than stock, same as stock, slightly louder? All these options are great but they are really complicating my planning! More than likely I'll stick with the XYZ, resonated pipe, and VQ exhaust.
just another question to throw out there, the VQ exhaust you have, just how "quite" is it.....more than stock, same as stock, slightly louder? All these options are great but they are really complicating my planning! More than likely I'll stick with the XYZ, resonated pipe, and VQ exhaust.
The VQ exhaust is similar to, or maybe even a little quiter than, the Fujitsubo for daily driving. ...And notably quieter at WOT high RPM.
You can clearly hear the VQ exhaust note at WOT but it doesn't scream at all.
Even with test pipes, its not loud.
Registered User
Joined: Jun 2008
Posts: 12
Likes: 0
Originally Posted by Hydrazine
The VQ closest comparison is to the Fujitsubo.
The VQ exhaust is similar to, or maybe even a little quiter than, the Fujitsubo for daily driving. ...And notably quieter at WOT high RPM.
You can clearly hear the VQ exhaust note at WOT but it doesn't scream at all.
Even with test pipes, its not loud.
The VQ exhaust is similar to, or maybe even a little quiter than, the Fujitsubo for daily driving. ...And notably quieter at WOT high RPM.
You can clearly hear the VQ exhaust note at WOT but it doesn't scream at all.
Even with test pipes, its not loud.
Last edited by trxjwb; Jul 21, 2008 at 01:04 PM.
Originally Posted by Hydrazine
What diameter is your HKS?
INFINITI G35 Sedan 2003 - up ;
Rear Section,
Stainless Steel Muffler Dual E1
Tip diameter 83mm
Piping diameter 65mm
Will it fit?
Former G35driver Vendor
iTrader: (23)
Joined: Jul 2004
Posts: 3,054
Likes: 85
From: Los Angeles California
Originally Posted by clinthammer
32008-BN001
INFINITI G35 Sedan 2003 - up ;
Rear Section,
Stainless Steel Muffler Dual E1
Tip diameter 83mm
Piping diameter 65mm
Will it fit?
INFINITI G35 Sedan 2003 - up ;
Rear Section,
Stainless Steel Muffler Dual E1
Tip diameter 83mm
Piping diameter 65mm
Will it fit?
Former G35driver Vendor
iTrader: (23)
Joined: Jul 2004
Posts: 3,054
Likes: 85
From: Los Angeles California
Originally Posted by trxjwb
Im looking for an exhaust for my 05 Sedan, Im looking for a clean look, I love the stock sound of the coupe's tone, I dont want one much louder than that. My question is there much of a gain at that sound level? My mods are your motordyne 1/2 inch spacer, mrev2, and technosquare tune with a stock exhaust.
Tony,
What's the plan with regards to 02 sensors, TPs, and cat converter aft of the y-pipe? Are you going to extend the 02 sensors to mount behind the cat or just leave them in place? Last year when I approached Warpspeed Performance about this setup, we weren't sure which avenue to take. I guess they didn't see much hope in the whole setup (TP->y-pipe->cat) and kept focus on their truck exhausts. Thier loss now
What's the plan with regards to 02 sensors, TPs, and cat converter aft of the y-pipe? Are you going to extend the 02 sensors to mount behind the cat or just leave them in place? Last year when I approached Warpspeed Performance about this setup, we weren't sure which avenue to take. I guess they didn't see much hope in the whole setup (TP->y-pipe->cat) and kept focus on their truck exhausts. Thier loss now
Former G35driver Vendor
iTrader: (23)
Joined: Jul 2004
Posts: 3,054
Likes: 85
From: Los Angeles California
Originally Posted by DaveB
Tony,
What's the plan with regards to 02 sensors, TPs, and cat converter aft of the y-pipe? Are you going to extend the 02 sensors to mount behind the cat or just leave them in place? Last year when I approached Warpspeed Performance about this setup, we weren't sure which avenue to take. I guess they didn't see much hope in the whole setup (TP->y-pipe->cat) and kept focus on their truck exhausts. Thier loss now
What's the plan with regards to 02 sensors, TPs, and cat converter aft of the y-pipe? Are you going to extend the 02 sensors to mount behind the cat or just leave them in place? Last year when I approached Warpspeed Performance about this setup, we weren't sure which avenue to take. I guess they didn't see much hope in the whole setup (TP->y-pipe->cat) and kept focus on their truck exhausts. Thier loss now
Got one for that.