Have a Question/s About Wheels/Tires/Offsets/Camber/Etc? Ask here::
#5956
Registered User
iTrader: (18)
Join Date: Sep 2007
Location: Auckland, New Zealand
Posts: 10,359
Received 1,939 Likes
on
1,249 Posts
Like i mentioned in my earlier post. I was hitting the coil with my 13 -8.
The 12 inch equivalent of that is +4. Which will mean you will probably rub if you run the same camber as me (-7 degrees) If you run less, you might be able to get away with +4. To make sure you can get away with it, go with lower offset than +4.
The 12 inch equivalent of that is +4. Which will mean you will probably rub if you run the same camber as me (-7 degrees) If you run less, you might be able to get away with +4. To make sure you can get away with it, go with lower offset than +4.
#5960
Tire Size?
My wheels are 20" 8.5F 10R dropped on coilovers. I am running 245/35/20 in the front and 275/30/20 in the rears. I need new tires in the front. I was thinking about getting 235/35/20 or 235/30/20 for the fronts to have that slight stretch like the rears tires have. Would this affect anything? What tire size do you recommend?
#5961
Torretto You run a 19x13? holy **** I guess i am not the only one going agro.
I've already got them in and about to put rubber on them but what is your opinion of a 06 sedan running Leon Hardiritt Bali's 19x11.5+16 rear and 19x10+22 front not rubbing as of yet. Going to swap the Tien Basics for some BC coils and trying to run a 245/35 on the rear with something similarly stretched on the front
Rear profile no pull yet
![](https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-frc3/p480x480/970532_544135635635460_513030573_n.jpg)
Front test fits
I've already got them in and about to put rubber on them but what is your opinion of a 06 sedan running Leon Hardiritt Bali's 19x11.5+16 rear and 19x10+22 front not rubbing as of yet. Going to swap the Tien Basics for some BC coils and trying to run a 245/35 on the rear with something similarly stretched on the front
Rear profile no pull yet
![](https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-frc3/p480x480/970532_544135635635460_513030573_n.jpg)
Front test fits
![](https://sphotos-a-atl.xx.fbcdn.net/hphotos-ash3/542230_544232942292396_1627803749_n.jpg)
#5963
Please help offfset question 20 x10
I found some wheels i want there for my g35x 2005 idk if these fit my car im lowered on Tein S 1.6'' back 2'' back ,or would i have to roll the fenders and pull them which is fine i just dont want to start messing with camber its my daily driver work and back etc and could i use 40series tires or would i have to get 30-35s there i drive to nyc some times would prefer 40's but idk about the rubbing issues i dont want them to stick out just flush with the quater panels after i roll them they are 20 x 10 ET 25 thanks for any help!
#5964
Okay, Just some reassurance is what I need.....
Current setup is
19x9.5 +4
19x10.5 +5
Going to
19x10 -10
19x11 -5
I should be fine correct. I will have a hair more poke I think but I barely rubbed as is will I be SCREWED when all is said and done? I have camber arms, but only want to run like 3-4 nothing much more than that.... I am rolled flat front and rear and also am slightly pulled. I guess I could pull more if needed...
Current setup is
19x9.5 +4
19x10.5 +5
Going to
19x10 -10
19x11 -5
I should be fine correct. I will have a hair more poke I think but I barely rubbed as is will I be SCREWED when all is said and done? I have camber arms, but only want to run like 3-4 nothing much more than that.... I am rolled flat front and rear and also am slightly pulled. I guess I could pull more if needed...
#5969
My specs are currently 19x10 -3 and 19x11 +3. My fronts are pulled a good amount and my rears are rolled flat. I think I have around 3* front and 5* rear of negative camber. I know it can be dialed in some more but there isn't much room. I might get it 1* positive.
Either way, you will be able to fit- stretched tires is a must
#5970