Wrathernaut's Double-Din Installation FAQ, Shopping and Resource List
The following users liked this post:
eagle3000 (04-06-2014)
The following users liked this post:
eagle3000 (04-29-2014)
#1480
Oh wow, so looking for that reverse wire I literally found 6 different ones. At that point I slapped on the plastic pieces I took off and then tested the new camera.
So, It turns on with the car
all that wasted work... So now when I turn the car on it automatically is there... But say I get to a destination and want the camera. Well then I have to go to the menu and turn it on.
So, It turns on with the car
![Mad](https://g35driver.com/forums/images/smilies/mad.gif)
The following users liked this post:
eagle3000 (04-29-2014)
#1481
I was finally able to install a Grom with bluetooth and I wanted to thank you for putting all of this information together. I was able to get it all done quickly due to this sticky. The only real problem was the screw by the dash clock, but that had nothing to do with lack of information or anything, just weakness on my part haha. But seriously, thanks again.
#1482
Anyway, to answer the original question, the ISVE61 is supposedly equivalent to the ROEM-NIS2, and it's what Best Buy uses. Considering there's been relatively few complaints about volume levels by people blaming best buy for their installation, I can only assume it has a pretty good success rating. However, the goal of the list is to keep things simple and cheap. Listing equivalent options that are more expensive to purchase (like the ISVE61) only serve to complicate things, so they won't be included in the list.
http://www.bestbuy.com/site/aamp-of-...VE61&cp=1&lp=1
You'd think keeping color consistency would be the primary objective.
Last edited by CuriousG; 05-05-2014 at 01:55 PM. Reason: spelling
#1483
So many props to Wrathernaut as I am almost done with my install.
However - I got the Axxess installed and trying to reprogram and no matter what the LED stays green (instead of the solid red in the manual). It autodetected the volume up/down, mode, seek up and seek down. I wanted to map pwr to mute and then swtich the seek up / down to presets, but seems I may be stuck.
Anyone else have this issue?
Once this is good it's almost time to put back together!
However - I got the Axxess installed and trying to reprogram and no matter what the LED stays green (instead of the solid red in the manual). It autodetected the volume up/down, mode, seek up and seek down. I wanted to map pwr to mute and then swtich the seek up / down to presets, but seems I may be stuck.
Anyone else have this issue?
Once this is good it's almost time to put back together!
#1484
So many props to Wrathernaut as I am almost done with my install.
However - I got the Axxess installed and trying to reprogram and no matter what the LED stays green (instead of the solid red in the manual). It autodetected the volume up/down, mode, seek up and seek down. I wanted to map pwr to mute and then swtich the seek up / down to presets, but seems I may be stuck.
Anyone else have this issue?
Once this is good it's almost time to put back together!
However - I got the Axxess installed and trying to reprogram and no matter what the LED stays green (instead of the solid red in the manual). It autodetected the volume up/down, mode, seek up and seek down. I wanted to map pwr to mute and then swtich the seek up / down to presets, but seems I may be stuck.
Anyone else have this issue?
Once this is good it's almost time to put back together!
http://contentdocs.installernet.com/...duct/34201.pdf
#1485
Just to be sure, these are the instructions you're following, right? (starting on page 16)
http://contentdocs.installernet.com/...duct/34201.pdf
http://contentdocs.installernet.com/...duct/34201.pdf
And one thing to note the trim ring for the new pioneer 5600 doesn't fit quite right since the headunit flips out, I sanded too much on it may need to try a different ring
Also I found a harness off the H/U that nothing goes to, what is that for?