PDA

View Full Version : Forced Induction


Pages : [1] 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39

  1. Thinking about purchasing a 2003 Greddy TT'd G35. Anything i should look for?
  2. 2005 G35 coupe TT issues...
  3. Early 03 G35 + Boost????
  4. Reducing final drive for a 5AT FI build
  5. Twins with exapump and oil cooler
  6. GT2554R to GT2871R with jwt manifolds
  7. Long time reader. First time poster.
  8. vortech setup
  9. Vq37 bottom end
  10. 2003 supercharged g35 guidance
  11. VQ35HR Swap to VQ35DE
  12. More boost, new numbers
  13. wanting to go FI
  14. High boost pulley
  15. Stillen high boost pulley
  16. Vortech v3 SCI tighten HELP
  17. G35 Build 2nd Try
  18. Throttle body probs
  19. Looking for a build to base mine on. Suggestions?
  20. Turbonetics revup kit on a non revup engine 07 g35
  21. APS CHRA's $900???? Has anyone done this?
  22. Best plenum for Vortech
  23. Stillen snout bearings part #
  24. Using a turbo from another vehicle.
  25. Single Turbo Oil Pressure
  26. 2006 G35 coupe ideas to FI
  27. g35 stalin
  28. need good advice
  29. Upgrading The Stillen Roots S/C MP62 to M90
  30. JWT 700BB Kit - Wastegate Actuator Spring Upgrade
  31. 8.8psi from Vortech v3 kit on 100k factory block
  32. Vortech in February - some rookie questions...
  33. Walbro 400 fuel pump melting factory plug.
  34. Piston repair estimate
  35. Injector size
  36. Berks HFCs
  37. Can I??
  38. Engine Blow up on Dyno - Questions
  39. Halp. pls.
  40. JdM rare harness cover
  41. TIME TO BOOST! Some questions
  42. Single turbo exhaust options
  43. 2004 g35 nos
  44. Turbonetics and 2006 power steering rack issue
  45. Super charger setup - No headers
  46. Supercharger kits , Vortech , GTM , HKS and Stillen...least, better, best experience
  47. Running rich under boost? power loss.
  48. Diagnosis help
  49. Problem holding boost at 20psi
  50. A Pillar Gauge Pod options
  51. Boost control
  52. up rev single turbo DTC code
  53. New numbers with more boost
  54. Vortech jack shaft bearings on '03 g35 quest
  55. How much boost/WHP can the stock fuel system push?
  56. Help!!! Blank ECU
  57. Boost loss after 4600rpm?
  58. High Compression boost?
  59. Modifying the Stillen Supercharger (de)
  60. Supercharge a High-Mileage Stock Engine?
  61. Looking for some help on adapter flange for v band
  62. Blower or a turbo?
  63. FMIC Charge pipe and AC lines
  64. Top Mounted TT'd added to current GTM Stage 2 TT Kit
  65. 34 row oil cooler
  66. Greddy manifold cracked. Fix or no? Any suggestions
  67. Need reliable shop for turbo rebuild
  68. AAM Competition WOW YEAR-END BUILD PROMOTION
  69. 2006 infiniti g35 5at twin turbo needa and recomended parts
  70. Innovate Wideband
  71. 2003 G35 Coupe 6MT-Need Twin Turbo
  72. Catch can/Crankcase venting?
  73. 2007 g35s sedan turbo or supcharger?
  74. Need help/advice: Greddy FMIC fabrication and single VS dual decision
  75. Vortech supercharger info pls
  76. Valve cover oil leak under boost?
  77. Stillen Supercharger or Greddy turbos
  78. Need help relocating this hose near blower (Vortech)
  79. JWT 700bb kit and Haltech Boost Control
  80. FI G owners - wannagofast.com 1/2 mile event
  81. Help with HKS SC
  82. Stillen SC Tensioner Help
  83. Vortech mikalor clamps
  84. 2006 Infiniti G35 *Hybrid Turbocharged*?
  85. 2005 Infiniti G35 TwinCharged
  86. power cuts out after full acceleration
  87. HELP single Turbo 2004 g35
  88. 1 Spark plug away from a tune.......
  89. Change clutch with GTM tt kit?
  90. issues with ecm wireing on 2003 CDN coupe
  91. Performance auto tranny and transfer case options?
  92. *** Easiest way to remove/repair cracked Greddy manifold*****
  93. Greddy TT install. Fuel line bracket
  94. Anti-Lag / Launch Options
  95. Open Wastegate Dumps, Finally
  96. i just received a new Turbo
  97. 272 Cams with 9.5:1 Compression
  98. ** Starting G up after been in storage for 2 years ****
  99. Progressive Nitrous Controller
  100. Greddy turbo manifold cracked..... weld???